| DESCRIPTION OF ENHANCEMENTS |
DESCRIPTION:
facilitate automatically purging the log. A post-init will run to clean
2. Unload the distribution
Use the INSTALL/CHECK MESSAGE option on the PackMan menu to unload
the KIDS distribution included with this message.
3. Stop all incoming filers.
On the 'Filer and Link Management Options' menu, select the
'Monitor, Start, Stop Filers' option. At that menu level, choose
the action 'Stop incoming filer' to stop each incoming filer.
up any existing TMP("MHV7LOG") entries.
4. Install the transport global.
From the Kernel Installation and Distribution System Menu,
select the Installation menu.
5. From this menu, you may elect to use the following options
(when prompted for INSTALL NAME, enter MHV*1.0*1):
a. Backup a Transport Global - this option will create a backup
message of any routines exported with the patch. It will NOT
backup any other changes such as DDs or templates.
b. Compare Transport Global to Current System - this option will
allow you to view all changes that will be made when the patch
is installed. It compares all components of the patch
(routines, DDs, templates, etc.).
c. Verify Checksums in Transport Global - this option will
allow you to ensure the integrity of the routines that are in
the transport global.
d. Print Transport Global - this option will allow you to view the
components of the KIDS build.
6. Use the 'Install Package(s)' option under the 'Installation' menu
A new menu, MHV LOG MENU, has been added. The log provides information
and select the package 'MHV*1.0*1'.
7. When prompted 'Want KIDS to Rebuild Menu Trees Upon Completion of
Install? YES//', Respond as fits your situation, see note above.
8. When prompted 'Want KIDS to INHIBIT LOGONs during the install?
YES//', respond NO.
9. When prompted 'Want to DISABLE Scheduled Options, Menu Options, and
Protocols? YES//', choose 'NO'.
of use to MHV developers, and should only be used by IRM staff in the
10. At the DEVICE prompt, you can send your output to any printer or
HFS file, display it on the terminal screen, or queue it to run
at a scheduled time.
11. After the install, restart the incoming filers.
On the 'Filer and Link Management Options' menu, select the
'Monitor, Start, Stop Filers' option. At that menu level, choose
the action 'Start incoming filer' to start the default number of
incoming filers.
event troubleshooting an MHV interface becomes necessary. The MHV user
12. Log on to each node running the HL7 listener and run the post init
Routine CLEANLOG^MHV1P1.
ROUTINE SUMMARY:
================
The following is a list of the routine(s) included in this patch. The
second line of each of these routine(s) will look like:
manual provides information on how to use these options.
<tab> ;;1.0;My HealtheVet;**1**;Aug 23, 2005
CHECK^XTSUMBLD results
Routine name Before Patch After Patch Patch List
============ ============ =========== ==========
MHV1P1 N/A 674288 1
MHV7R1 7907937 7704915 1
MHV7R2 8857636 8693511 1
MHV7U 6547453 7067072 1
Included options are:
MHVUL1 N/A 5527922 1
MHVUL2 N/A 5279644 1
MHVUL3 N/A 10342175 1
MHV LOG CONFIG Configure Logging Parameters
MHV LOG INFO Display Log Information
============
MHV LOG OFF Turn Off Logging
MHV LOG ON Turn On Logging
MHV LOG PURGE Purge Log
MHV LOG SIZE Display Log Size
MHV LOG VIEW View Log Entries
A new option has been added, MHV CLIENT, as a broker context for a future
MHV GUI client. The following remote procedures are also included:
MHV LOG INFO
MHV LOG OFF
MHV LOG ON
MHV LOG PURGE
MHV LOG SIZE
MHV LOG CONFIG
MHV LOG SUMMARY
MHV LOG DETAIL
The MHV 1.0 release went to the field with two HL7 protocols having the
"debug" flag set. These event driver protocols will be released with the
flag turned off. The following protocols are being shipped:
The MHV 1.0 release for MHV Rx Refill went to the field with logging to a
MHV OMP-O09 Event Driver
MHV OMP-O09 Subscriber
MHV QBP-Q13 Event Driver
MHV QBP-Q13 Subscriber
Associated Remedy Ticket
====================
HD 131029
TMP global left on. The non-standard use of TMP by the MHV log causes
Test Sites
==========
Tampa VAMC
Bay Pines VAMC
Baltimore VAMC
VISN 2
INSTALLATION INSTRUCTIONS
==========================
the TMP entries to not be cleaned up automatically.
The patch is distributed in KIDS format in a PackMan message.
This patch requires MHV 1.0
**WARNING**
Inbound HL7 messages for MHV should not be processed during installation
of this patch. All incoming filers should be stopped before installation.
This patch will turn off logging in the HL7 receiver routines allowing it
Before you install this patch in production, please identify all the
production node(s) that have the TMP("MHV7LOG") global. This should be
the same node(s) running the HL7 Listener. You will need to log on to
each of these node(s) and run the post-init routine CLEANLOG^MHV1P1 will
delete the global entries since TMP is not translated. The
TMP("MHV7LOG") global should have many entries.
****
to be switched on and off externally as designed. An XTMP global will be
**Notice**
This patch includes new options.
When an option is included in the patch build, the question REBUILD MENUS
is asked as a PRE-INSTALL question. If you choose to have KIDs rebuild
the menus it will happen at the end of the build installation and may
take several hours.
Note: Most sites have a nightly batch job that rebuilds the menus so if
you queued the installations ensure that it will complete prior to the
batch job. Or, if you are installing several builds, wait until the
used instead of TMP. Options will be added to control logging and to
last one to use the KIDs rebuild functionality.
****
The install time for this patch is less than 5 minutes. This patch can be
installed with users on the system.
1. These routines should not be mapped.
|
